Engenharia Mecânica
URI permanente desta comunidadehttps://repositorio.fei.edu.br/handle/FEI/23
Navegar
3 resultados
Resultados da Pesquisa
- Surface integrity analysis in machining of hardened AISI 4140 steel(2017-01-23) STIPKOVIC, M. A.; Ed Claudio Bordinassi; Farias, Adalto; Sergio DelijaicovThis study aimed to analyze the residual stresses and roughness in finishing milling of AISI 4140 steel, quenched and tempered up to hardness of 58 HRC. Machining operations were performed with the use of CBN inserts and by varying three basic cutting parameters (cutting speed, feed per tooth and cutting depth). Hardened materials are typically machined by abrasive processes, which in turn are more expensive and complex to be studied due to the undefined cutting geometry of the grinding wheel. A series of machining tests with milling process and CBN tools was implemented in order to study the resultant condition of the specimeńs surface. An experimental design was used and the results were statistically treated, enabling the generation of a model that aims to obtain roughness values due to the optimization of three adopted cutting parameters. The roughness values found in the range of Ra 0,16 to 0,4 μm indicate that it is possible to use the milling process with CBN tools for finishing, reducing machining time and the cost of the machined part. The generated residual stresses were compressive and the feed per tooth parameter showed greater influence in this result. The research was limited to test only one type of CBN insert, which was constantly replaced, preventing the influence of tool wear on responses. The geometry of the tool as well as the use of cutting fluid were not considered. Milling process with CBN inserts is confirmed as a possibility for replacing grinding process for finishing machining leading to significant gains in machining time. An optimized model was derived to predict the value of the roughness and three optimizations were made to specify the best cutting parameters to desirable answers such as better roughness, higher compressive residual stresses and low cutting forces, for example.
- Surface integrity of INCONEL 718 turned under cryogenic conditions at high cutting speeds(2019-06-26) PEREIRA, W. H.; Sergio Delijaicov© 2019, Springer-Verlag London Ltd., part of Springer Nature.Nickel alloys such as Inconel 718 have been widely used in the aerospace, oil and gas, and chemical industries, since they have excellent properties that combine high creep resistance and high mechanical strength, fatigue and corrosion. However, these properties make these alloys extremely difficult to machine, due to a high level of heat generation during material removal, causing rapid wear of cutting tools and a detrimental effect on the surface integrity, reducing the fatigue life of the machined component and lowering the productivity. Looking at the literature, it seemed that there is an opportunity to study the surface integrity of Inconel 718, turned under cryogenic conditions at cutting speeds of 250, 275 and 300 m/min. For these reasons, this work aims to evaluate the influence of the cutting parameters on the surface integrity of Inconel 718 turned under cryogenic conditions using liquid nitrogen (LN2) at high cutting speeds. A whisker-reinforced ceramic tool was used in order to provide wear and shock resistance at high cutting speeds; these are factors that are associated with surface integrity in terms of roughness Ra, residual stresses, microhardness and cutting forces. A central composite design was chosen as factorial planning for the independent variables including cutting speed, feed rate and depth of cut when carrying out the experiments. Cryogenic cooling resulted in an average cutting force of 267 N, where the penetration force was higher. The roughness Ra was 0.52 μm and was influenced by the feed rate and depth of cut. The highest tensile residual stresses in the circumferential direction with LN2 and under dry conditions were 1394 MPa and 1237 MPa, respectively and were influenced by the depth of cut. Small changes in microhardness occurred at a depth of 0.3 mm from beneath machine surface and the presence of a white layer was not observed. Although tensile residual stresses were slightly higher when using LN2 compared to dry machining on the surface, the use of LN2 caused higher compressive residual stresses at the subsurface, which can improve the fatigue life of machined components at high cutting speeds. The results showed that lower cutting parameters tend to give the best results in terms of the cutting force and surface integrity.
- Analysis of surface integrity for din 100cr6 steel conical bearing rings after hard turning(2011-11-12) Sergio Delijaicov; SALAZAR, C. E. V.; BORDINASSI, E. C.; PADOVESE, L. R.This work studies the influence of machining parameters, such as cutting speed and forces, feed rate, cutting depth, and tool flank wear, on the generation of surface residual stresses in DIN 100Cr6 steel conical bearing rings submitted to a hard turning process. A complete factorial planning was used to perform the tests and projected measurement. Cutting forces were measured by a piezoelectric dynamometer and residual stresses were determined by the hole-drilling method using strain gage. Results showed that after 2000 m of tool machining, phase transformations had been observed on sample surfaces, with white layer formation, and deeper, a dark layer whose thickness varied depending on the severity level of turning and the tool wear (in machined distance). Increase in tool wear generated minor values of compressive residual stresses and the surface roughness presented almost the same values in all experiments, except when the bigger parameters were used. © (2011) Trans Tech Publication.